Slash Your Stash Quilt

Slash Your Stash Quilt
Slash Your Stash Quilt
Designed by
All Rights Reserved

Here I'll show you how to sew this lovely "slash your stash" quilt. There are step by step photos to help you in this process.

You will need

twelve different squares of fabric (15" by 15")
one small safety pin
a ruler longer than 15"
a rotary cutter (with the sharpest blade you have)
a 12 1/2" square ruler for square up the blocks
sewing machine

What you do

Above you can see the fabrics I chose to make this sample quilt. Now, I have to explain that I'm making a much smaller quilt for this demonstration. (Should have taken my camera with me when I made the larger one--rookie mistake!) I am making only six total squares. But the procedure is the same.


When you have the pieces all cut out, lay them, edges aligning, in a stack. Lay The Ruler on top of the stack, and Make A Cut anywhere, dividing the stack into two stacks. The only caveat is that you shouldn't be closer than about 2 inches from any corner, just to make it simpler. Twelve pieces of fabric is a lot to cut through. If you can't physically do it, separate your stack into two stacks of six squares and cut them separately. Just make sure that the two cutting lines are exactly the same.

Now is when you need to Put A Safety Pin in the upper-right-hand corner of only the topmost fabric square. This will help you to keep track of where you are as you go along. The safety pin should Always be in that upper-right-hand corner of (in my case) the blue polka dot fabric. I know that it sounds unnecessary to do this. That it shouldn't be too hard to keep track of this stack of fabrics. Just trust me on this one--you will undoubtedly be glad in the end that you have a pin there. I know I was.

Now, Take That Top Cut Piece of Fabric on the Left Side and Place it at the Bottom of the Left-Hand Stack.

Now your stacks look like this. Above you see the light blue piece on the left has gone underneath all those other fabrics. Now we're going to Sew Together each two-piece layer of our fabrics.
With me so far?

This photo shows how I have laid the right-hand fabric over onto the left-hand fabric, then I'll just sew it down the right-hand side with a 1/4" seam. Don't worry if the edges don't come out exactly even. We're going to even them all up at the end.

Here are the next two fabrics to be sewn together. It Is Essential* that you keep track of which square you sewed together first, second, etc. to make the pattern work right.

This is definitely a good time for chain-piecing (not breaking the threads between seams). It is practical, and a good way to keep your squares in the right order.

When you have your long chain of twelve squares sewn back together, take them (in one long string) to the ironing board and Press The Seams To One Side. If you prefer, you may press them open, it doesn't really matter.

1. Iron seam flat on first square.
2. Cut it off from the second square.
3. Place the first piece up-side-down on your table.
4. Repeat 1. through 3. till everything is pressed.

This is my new stack of squares. I'm lifting up the layers to show them to you.

Now it's time for the second cut! (Don't get too excited!!)
Lay the ruler down again on top of the stack and Make Another Cut in Another Direction.

Now we're going to Take The Top Two Layers (on the left-hand side) and Put Them On The Bottom Of The Stack. See how I'm demonstrating this in the above photo?!!

Again, Re-Sew the Squares Together with the new combination, chain piecing them. Then Press as before (the steps 1. through 4. above).

Then you'll make the Third Cut. Lay the ruler so it bisects at least one of the previous two seams, and "Whack" again!

This time you'll be Moving The Top Three Layers (from the left side) To The Bottom Of The Stack.

It's easy to remember.
First cut -- move one layer.
Second cut -- move two layers.
Third cut -- move three layers.

And again, Sew Them Back Together. Almost done!

Last step is to take your 12 1/2" square ruler and Square Up All Those Edges.

This shows all six of my squares laid out together. (Remember, I made a "mini-version." You will have twelve squares.)

They look a little like a crazy quilt, don't they!? The blocks have the appearance of having been pieced with lots of smaller, irregular pieces. But you and I know better than that, don't we!

Now you can play with them on your design wall and decide how you want to put them together. Personally, I like to just sew the squares together. But you can add sashing if you want. The photo below gives a hint of what it would look like if I used yellow fabric for the sashing. OK, maybe that's a little too much yellow, but you see what I am getting at!

Now, how about if I added some of the lavender for a border? This just gives you an idea of what you can do with your squares.

Adding sashing and border(s) alters the size of your quilt, obviously. If you add no other fabric, it will measure 36" wide by 48."

Now you have all the instructions. I would love to see it if you make a quilt of your own. I will show you when this one is all finished, too.

*Remember when I said it was essential to keep your fabrics in the right order to make the pattern work? If for some reason your squares didn't turn out exactly as they should, if something went together wrong, don't worry about it! This block is supposed to look very random and mixed-up. If you made a mistake when you were moving the layers, or sewing them together, or if they got out of order, it will all look fine in the end.


About The Author

Janice Carter is a California blogger who enjoys a variety of crafting projects. Check out her blog, MissesStitches.